Condition: used, Cut-to-length line Delta-Alcos 72”x0.5”x60,000Lb (A3770) Make: Delta / Alcos Material Width: 36" - 72" Thickness Capacity: .048" - .530" Weight Capacity: 60,000Lbs Coil ID: 16" - 24" Coil OD: 72" Yield Strength: 50,000PSI Direction: Right to Left Coil Storage Conveyor Entry Coil Car Hydraulic Lift and Traverse Cone Uncoiler DC Motorized Brake Sliding Base Wichita Cooled Brake Powered Hold-Down Roll Hydraulic Peeling Table Powered In & Out Set of Driven Pinch Rolls Delta Corrective Plate 4-Hi Leveler Number of Work Rolls: 9 Work Roll Diameter: 8" Work Roll Width: 82" Powered Up & Down Back-Up Flights DC Motor & Drive Delta Corrective 4-Hi Leveler Number of Work Rolls: 19 Work Roll Diameter: 4" Work Roll Width: 82" Motorized Back-Up Flights Powered Work Roll Adjustment Ndedpfeixqg Nex Agzsc DC Motor & Drive Alcos Mechanical Shear Down Cut Shear Driven Entry Pinch Rolls Pneumatic Clutch & Brake AC Motor Drive Alcos Drop Type Stacker 40' Sheet Length Driven Exit & End Conveyrors Touch Screen Digital Panel Operator Push Botton Station Digital Read Outs Hydraulics, Electrics, Controls, Presently Installed

Condition: used, Year of construction: 2024, INDEX MS22-8 Mfd. 2024 2 NCU (4) Y-Axis SL Control Cutting hours: 1,000 Turnkey Available Located in Europe 4-Meter IEMCA SIR MS22-8/43/P Rack loader 50 Hz D9-13-19-25 Bar length 4300 mm with drilling unit and minimum quantity lubrication unit additional end-of-bar sensor Bar stock 500mm (D12-D24) Bar stock 340 mm (D5-D11). Additional storage chain for 22 bars with Profinet interface. 1 11007253 (21711) 1 set (8 pieces) bar stock pushers, external clamping for bar stock diameters D7-D10 mm, internal clamping for bar stock diameters D13-D18 mm, consisting of: 8 bar stock pushers D12 8 rotating sleeves D12 1 10287026 (21712) 1 set (8 pieces) bar stock pushers, external clamping for bar stock diameters D11-D16 mm, internal clamping for bar stock diameters D19-D24 mm, consisting of: Nodoxnrtcepfx Agzedc 8 bar stock pushers D18 8 rotating sleeves D18 1 10536056 (21713) 1 set (8 pieces) bar stock pushers for bar diameters D17 mm-D22 mm, consisting of: 8 bar stock pushers D23 8 rotating sleeves D23 1 10414481 (21702) 1 set (8 pcs.) of internal clamping sleeves D12mm for bar diameters D13 mm - D18 mm Drill diameter D8 mm. 1 10472413 (21704) 1 set (8 pcs.) of external stops D12 mm for bar diameters D13 mm - D18 mm pre-machined. 1 10264327 (21703) 1 set (8 pcs.) of internal clamping sleeves D18mm for bar diameters D19 mm - D24 mm Drill diameter D15mm. 1 10058206 (21705) 1 set (8 pcs.) of external stops D18 mm for bar diameter D19 mm - D24 mm pre-machined. 1 12123486 Drill for drilling unit consisting of: 1 indexable insert drill D 15 mm 10 indexable inserts for steel 2 solid carbide drills D 8 mm

Year of construction: 2018, condition: ready for operation (used), Control Unit Brand HAAS Main Drive Spindle speed range 2400 rpm Spindle motor power 40 hp Number of axis 2 Tail Stock Pinol tool taper MT5 Media Chip conveyor Yes Additional Equipment Line Filter & Surge Suppressor – 220 VAC, 3-phase, 80 A, 60 Hz Early Power-Failure Detection Module Belt-Type Chip Conveyor This HAAS ST-40 was manufactured in 2018. It features a 15-inch chuck, a maximum part swing of 35.5 inches, and a cutting diameter of 30 inches. The machine includes a 2-speed gearbox spindle, capable of 2,400 rpm, and a 12-station BOT turret. Additional equipment includes a belt-type chip conveyor and a programmable servo tailstock. Consider the opportunity to buy this HAAS ST-40 horizontal turning machine. Contact us for more information about this machine. Application Types Nedpfxexp Sl Ue Agzodc Turning

Condition: new, functionality: fully functional, Year of construction: 2024, machine/vehicle number: 50, laser power: 12,000 W, cutting speed: 100 mm/min, workpiece weight (max.): 1,500 kg, total length: 260,000 mm, warranty duration: 60 months, working range: 715 mm, Equipment: cooling unit, HSG Laser | TX 3+1 Heavy-duty Tube Fiber Laser Cutting Machine Size: 7026mm, 9032mm, 12036mm, 12050mm Laser source power: 3000 - 12000W Cutting Capacity: Round tube: Φ15-500 (TL Φ15-715); Square tube: □15*15 - 350*350 Rectangular diagonal ≤ 500mm Optional function: automatic loading and unloading system Nsdpfortiirsx Agzodc 3+1 Twin-chucks Clamping Cutting Technique

Condition: good (used), Year of construction: 2019, machine/vehicle number: 25653, Equipped with: -Automatic Central Lubrication System -Machine Guard -Indramat - MTX and Sercos CNC Control -The standard machine is equipped with CNC-control make Indramat - MTX and SERCOS-interface -Tool Dressing (Automatic dressing cycle of the dressing master and honing wheel tip diameter by a diamond coated dressing roll. The dressing cycle of workpieces can be pre-selected) -Electronic Indexing Unit -Operator and Maintenance Manual -All Electrical Drawings -PLC Language in English -Software and Hardware for Remote Diagnosis -High Precision Control of the Stock Allowance Material -Manual Loading on Spindle for Prototypes -Software for Infeed Optimized Cycle Type Reduction (Adaptive Honing) -Software for Vario Speed Dressing -Software for Calibration of Master Gears -Software for Timing Gears (including additional sensor for the hole of 4mm) -Software for Shortening of Workpiece Change-Over Time -Clamping Cylinder -RITTAL Cooling Unit -Lighting for Working Area -Installation of Vibration Detecting Sensors -Coolant Unit -Electrostatic Oil Mist Exhauster IFS With Rigid Piping -Internal Automation -Pallet Ring Conveyor System FlexLink (L-form shape see approved layout) -Parallel - Double Gripper -Pick and Placer Between Pallet Conveyor and Internal Loader -Extended Loading Length of the Pick and Placer Specifications: Workpiece: Nodpfx Agow Iquyozjdc -Part Diameter: 20-150 mm -Maximum Face Width: 70 mm -Part Weight: 20 kg -Number of Teeth: 6-150 -Module: 1-5 mm Workpiece Spindle: -Maximum Speed: 6000 1/min -Installed Power: Approx. 25 kW Tool: -OD of Honing Wheel: 270 mm -Widths of Honing Wheel: 20-70 mm -Honing Wheel Material: Ceramics Tool Spindle: -Maximum Speed: 2000 1/min -Installed Power: Approx. 25 kW Machine: -Total Connected Load, Approx: 70 kVA -Floor Space (w x l x H): -Total Weight, Approx: 11 Ton -Bosch Rexroth MTX Control CML 85 Longitudinal Slide, Z-Axis: -Linear Drive -Drive Torque: 3,700 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 400 mm Cross Slide, X-Axis: -Linear Drive -Drive Momentum: 2,150 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 1050 mm Swiveling Axis, W-Axis: -AC-Servo Drive: 10,000 1/min -Setable Gear Transmission: i=5000:1 -Swiveling Angle: -90 Degrees / +16 Degrees Workpiece Spindle, C-Axis: -Direct Drive, Maximum RPM: 7,000 1/min -Drive Power: 30 kW -Drive Torque: 112 Nm -Digital Measuring System Tool Spindle, B-Axis: -Direct Drive (hollow spindle drive), Maximum RPM: 2000 1/min -Drive Power: 30 kW -Drive Torque: 150 Nm -Digital Measuring System

Condition: used, Cut-to-length line Pro-Eco with Cassette Type Precision Leveler 60 x .187 x 50,000Lbs (A3789) Maker: Pro-Eco Excellent conditions SPECIFICATIONS: MAX WIDTH 60" MAX THICKNESS 187" MANUFACTURER - PRO-ECO YEAR - 1985, REINSTALLED 2002 WIDTH RANGE - 8" to 60" GAUGE RANGE - .024" to .187" WEIGHT CAPACITY - 50,000# (25 TON) COIL OD - 36" to 72" COIL ID - 19" to 24" SHEET LENGTH - 24" to 168" SHEET WIDTH - 8" to 62" PACK HEIGHT - 30" (INCLUDING DUNNAGE) PACK WEIGHT - 20,000# LINE DIRECTION - RIGHT to LEFT LINE SPEED - 50 to 300 FPM (VARIABLE) LEVELER TYPE - MECHANICAL WEDGE STYLE w/ TWO CASSETTES LINE COMPONENTS: FOUR ARM ENTRY STORAGE TURNSTILE FLOOR LEVEL COIL LOADING CAR CANTILEVERED MANDREL UNCOILER w/ WATER COOLED BRAKE PIVOTING AND TELESCOPING PEELER BLADE ENTRY PINCH ROLLS ROLLER TYPE SIDE GUIDES ENTRY CROP SHEAR SIDE TRIMMER HYDRAULIC SERVO DRIVE (CURRENTLY NOT OPERATIONAL) MECHANICAL STYLE LEVELER FRAME W/ 200 HP MOTOR CASSETTE #1 - 19 ROLL, 2.50" DIAMETER, 5 HI, 7 BACKUP FLIGHTS Njdpfxsthg Die Agzedc CASSETTE #2 - 19 ROLL, 1.75" DIAMETER, 5 HI, 7 BACKUP FLIGHTS STRIP INSPECTION AND CARRY-OVER TABLE w/ NON-MARKING ROLLS LOOPING PIT QUADRANT TABLES w/ NON-MARKING ROLLS ROLLER TYPE STRIP SQUARING TABLE PRECISION ROLL FEEDER W/ 55 HP MOTOR HIGH SPEED MECHANICAL CUT OFF SHEAR W/ 40 HP MOTOR BLANK INSPECTION CONVEYOR w/ NON-MARKING BELT REJECT BELT CONVEYOR w/ NON-MARKING BELT AND SCRAP CART 14 FOOT AIR FLOAT STACKER w/ SQUARING GUIDES AND END STOP 14 FOOT STACKER LIFT CONVEYOR w/ END DISCHARGE ROLLERS 14 FOOT STACKER RUNOUT CONVEYOR w/ END DISCHARGE ROLLERS OPERATOR CONTROL STATIONS UPDATED AC CONTROLS w/ ALLEN BRADLEY "CONTROL LOGIX" PLC (2006) UPDATED DRIVE CONTROLS w/ SIEMENS "SIMOREG" CONTROLLERS (2006) CLOSED LOOP HYDRAULIC SYSTEM CLOSED LOOP WATER COOLING SYSTEM

Condition: good (used), Year of construction: 2006, INDEX MS52C CNC Multi-Spindle Mfd. 2006 Control: Siemens 840D 6 Spindles 52mm Capacity Equipped as pictured Under power Knoll System Chip Conveyor Riedel Chiller 3.6 meter (12ft) IEMCA SIR Bar Feed Ndodpfxot Rkzwo Agzoc SIR MS52/F Type 38 XL Mfd. 2005

Condition: good (used), Year of construction: 2001, Equipped with: Power Stock Fanuc 5-Axis CNC Control 160M 400mm Honing Wheel X Axis Pulse Generator Coolant System w/Twin Filters Magnetic Chip Separator Honing Tool Set up for Last Job is Still in Machine Internal Diameter of Honing Tool on Machine is 14" Work Light Power Door Auto Dress 5-Part Program Instruction Book for 16M Control Instruction Book for Set-Up and Operation Specifications: Maximum Outer Diameter: 250 (350) Minimum Outer Diameter: 30 Maximum Overall Length: 400mm Maximum Tooth Width: 45mm Module: 1.0-3.0 Cross Feed Device(Z Axis): 430mm Max. Travel Ndsdperualpofx Agzsc Honing Wheel Cutting Feed Device(X Axis): 370 Max. Travel Honing Wheel Swing Device(C Axis): Swing Angle: +30 Degress Honing Wheel Rotation Drive Device(A Axis): Honing Wheel Spindle Speed R/Min: 500 Honing Wheel Outer Dia.: 300 (400) Maximum Honing Wheel Width: 50mm Crowning Device (Y Axis): Maximum Rocking Angle: 1.6 Degrees Motor Types: Z-Axis Drive Motor: 1.8Kw X-Axis Drive Motor: 1.8Kw Y-Axis Drive Motor: 0.7Kw C-Axis Drive Motor: 1.8Kw A-Axis Drive Motor: 2.2/3.7Kw Maximum Distance Between Centers: 600mm Center Height: 1,100mm Floor Space: 2,170W X 2,800D X 2,100H Mass Of Machine: 4,500Kg

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Ndodpfx Aoihf Ufjgzsc Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Condition: good (used), Year of construction: 1980, Davenport Model B 3/4" Mfd. in 1980s Pickoff / Back Finish Threading Ndsdpfx Ageh I Euaozjc Stock Reel and Stand Chip Conveyor Noise Tamer Sound Enclosure Refurbished and Ready to Run Several similar machines available

Condition: good (used), Year of construction: 2002, LANDIS 3SE 14"x 60"ANGLEHEAD CNC GRINDER REBUILT BY LANDIS & TOOLED 2002 Equipped with: NEW FANUC CONTROL 2007 2-Axis Template Truform Servo Step Profile 30 Degree 30" Wheel Dead Headstock Table Traverse Marposs E39 Marposs Table Gauge Lateral Locator 3-Gauge TIR Gauge Steady Rests Wheel Balance Servo Motor-Traverse Stepping Motor Mist Collector Specifications: Swing: 14" Center Distance: 60" Motor: 1200 rpm Motor Pulley Diameter: 7.031" Spindle Pulley Diameter: 6.5" New Wheel Diameter: 30" Worn Wheel Diameter: 22" Max. Wheel: 8500 sfpm Max. Workhead: 333rpm X-Axis Ball Screw Pitch: 5mm per rev. X-Axis Total Stroke: 14.74" X-Axis Motor Pully Wheel Feed Diameter: 3" X-Axis Ball Screw Pulley Diameter: 3" Z-Axis Ball Screw Pitch: 10mm per rev. Z-Axis Total Stroke: 72.88" Z-Axis Motor Pulley Diameter: 3" Z-Axis Ball Screw Pulley Diameter: 6" Total Stroke: +/-2mm Total Marposs Voltage Output: =/-10vdc Dresser One Revolution of the Stepping Motor: .045" Diamond One Revolution of the Stepping Motor: .005" Njdpfertr Eajx Agzodc Weight: 25,000 lbs.

Condition: used, Coil Width: 12″ – 60″ Material Thickness: .015″-.135″ Ndjdpfxeihf Tpo Agzjc Coil ID: 20″-24″ Speed: 180 fpm Direction: Left to Right Entry Floor Standing Coil Car Mandrel Uncoiler with Powered Expansion Motorized Hold-Down Roll Feed-Up Drive Hydraulic Peeler 9-Roll Coil Straightener with 4″ Work Rolls Driven Entry Pinch Rolls 40HP Motor Adjustable Hump Table Mechanical Shear Belt Conveyor with Positive Stop Device Air Gate Sheet Stacker, with Two Section of Gravity Rolls

Condition: excellent (used), Year of construction: 2000, INDEX ABC CNC Lathe. Mfd. 2000 Control: Siemens 840C Capacity 65mm Ran oil Still in production, running nylon With 12-ft Bar Feed (pictured) Chip Conveyor Comes the a good amount of tooling Control Type: Siemens SINUMERIK 840C Spindle Speed (max.): 6,000 RPM Power Requirements (V/Hz/PH): 400/60/3 Main Spindle Speed (max.): 6,000 RPM Bar Capacity: 65 mm Power: 20 kW (at 100%) Power: 27 kW (at 40%) Synchronous Spindle Speed (max.): 4,500 RPM Power (max.): 4.2 kW Capacity Tool Carrier 1: 8 (7 + synchronous spindle) Tool Carrier 2: 6 Ndedpow Td U Rofx Agzjc Dimensions Bar Feeder: L 150" x W 27" x H 52" Turning Center: L 80" x W 48" x H 65" Power Enclosure: L 52" x W 18" x H 70" Chip Conveyor: L 88" x W 48" x H 35"

Condition: good (used), Year of construction: 2013, TOYODA (JTEKT) GL32M-63 CNC UNIVERSAL CYLINDRICAL GRINDER Ndodertrzpepfx Agzoc Equipped with: CBN Grinding Wheel Flagging Steady Rest Workhead Mounted Rotary Dresser Marposs P3SE System Monitoring Toyoda In Process Gaging Marposs E20N Acoustic Controller Air Gap Eliminator Workpiece Collision Control Coolant Pumps W/Magnetic Separator Pendant Control RH Workhead with Center LH Workhead with Center Work Rests Worklight Light Curtains Stacklight Extra Wheels Specifications: -Grind Center to Floor: 1,000 mm -Swing Over Table: 320 mm -Distance Between Centers: 630 mm -Grinding Diameter Range: 10 - 150 mm -Floor Space (Base machine w/auxiliary equipment): 3,400 x 5,000 mm -Net Machine Mass (approx.): 10,500 kg Grinding Wheel: -Type: CBN Wheel -Wheel Size (OD): 350 mm -Maximum Wheel Width: 60 mm -Surface Speed: 120 m/s Wheelhead: -Spindle Bearing: TOYODA STAT Bearing -Slide: V and Flat -Feed System: Ballscrew -Rapid Feed (on diameter): 30 m/min -Minimum Incsrement (on diameter): 0.0001 mm Workhead: -Type: Dead Spindle -Work Speed (Max): 500 rpm -Center Taper: MT #4 Footstock: -Type: Hydraulic -Taper Compensation: Manual -Maximum Center Retraction: 60 mm -Center Taper: MT #4 Motors: -Wheel Drive Motor: 15 kW, Belt-Drive -Wheelhead Feed Servomotor: 1.3 kW Tank Capacities: -Wheel Spindle Lubrication Oil: 80 L -Hydraulic/Lubrication Oil: 20 L

Condition: used, 72″ x .187″ x 20,000Lb Universal Slitting Line Material Width: 12″ – 72″ Material Thickness: .015″ – .187″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry Floor Standing Coil Car L-Type Design Ndedpfx Aoihf Twjgzoc Hydraulic Lift & Traverse Mandrel Uncoiler Powered Hold-Down Roll Hydraulic Expansion Air Cooling Brake Sliding Base Hydraulic Peeling Table Slitting Head Arbor Diameter: 7″ Powered Arbor Adjustment 100HP DC Motor Knives & Tooling Recoiler Powered Push-Off Hydraulic Over-Arm Separator Hydraulic Expansion 100HP DC Motor Exit 2-Arm Turnstile Arm Width: 72″ Powered Rotation Complete Slitter with Electrics, Hydraulics, Controls, Tooling

Condition: excellent (used), Year of construction: 1999, Citizen BL-12 CNC Swiss Style Mfd. 1999 Mfg No. BL12 12/0073 SN: L10037 Comes with Bar Feeder (not pictured) Ndodpew Sx U Aofx Agzoc Machine has no guide bushing (chucker mode only) Machine has no sub-spindle Spindle Bore Diameter: 0.5″ (~12.7 mm) Spindle Power: 3 hp (~2.2 kW) Maximum RPM: 12,000 rpm CNC Control: (typical) Fanuc 21i-TA or equivalent Tool Configuration: Gang/boring setup, front & rear stations

Condition: good (used), Year of construction: 2003, NAGEL MODEL TBT M320-6 6 SPINDLE CNC HORIZONTAL GUN DRILL, 2003 Equipped with: Panel Mate Power Pro Control Counter Rotation Cross Drilling High Pressure Coolant System Auto Loader Magnetic Chip Separator Hydraulic System Chiller Nodpfsrtrztex Agzsdc Specifications: Maximum Drill Depth (Approx): 16" Maximum Drill Length: 36" Number of Drill Spindles: 6 Spindle Motors (3): 7.5HP HP Per Spindle: 3.75 Drill Head Slide Stroke: 16.9" Maximum Diameter Mild Steel: 0.750"

Condition: excellent (used), Traub TNL12 CNC Swiss 12mm Capacity Production hours: 25596 hr. Kraft & Bauer Fire Suppression System Paper filter: Kompatkt Band Filter Configured as pictured (more photos to follow) Put into production in 2009 (originally show model) 12-ft FMB Bar Feed Mist Collector Ndodpfxow R E Ado Agzjc Chip Conveyor “2 machines available”

Condition: good (used), Year of construction: 2013, total length: 3,990 mm, total height: 2,500 mm, total width: 2,280 mm, overall weight: 8,500 kg, INGERSOLL CM SYSTEMS AOHD AGILE OIL HOLE DRILL Equipped with: Siemens 840D Control (2) Drill Heads 20-Tool Rack HSK 50A Taper (2) 7" 3-Jaw Chucks (2) Tailstocks (2) Steady Rests Chip Auger Chip Conveyor Mist Collector Hydraulic System Q R 2 Lube System Air Compressor Specifications: Maximum Length: 1050 mm (41.3") Minimum Length: 180.0 mm (7.1") Maximum Stroke: 250.00 mm Maximum Main Journal Diameter: 115.0 mm (4.5") Maximum Pin Journal Diameter: 100.00 mm (3.9") Maximum Swing Diameter: 250.0 mm (9.84") X-Axis Travel: 1450 mm (57.1") Y-Axis Travel: 150 mm (5.9")W/HSK 50 Z-Axis Travel: 305.0 mm (12.0") A-Axis Travel: 360 Degree B-Axis Travel: 90 Degree Feed Rate (Z): 1 m/min Maxim (40"/min max) Position Accuracy of X,Y,Z Axes: .010 mm (.00039") Position Accuracy of A & B Axes: .03 Degree Position Repeatability of X,Y,Z Axes: .005 mm (.0002") Position Repeatability of A & B Axes: .005 Degree Spindle Power: 5.5 kW (7.5 hp) Spindle Speed: 0-6,900 RPM Ndsdpsrtrx Rsfx Agzoc Tool Adaption: HSK 50E or A Tool Storage (ATC): 20 Total - 10 Per Spindle W/HSK 50 Lubrication - Slides & Ball Screws: Automatic Central Lubricator Approximate Floor Space (LxWxH): 4.0 x 2.3 x 2.5 m (13.1 x 7.5 x 8.2 Ft) Approximate Machine Weight: 8,500 kg (18,740 #)

Condition: good (used), Year of construction: 2011, LANDIS LT-2 TWIN WHEEL CNC ORBITAL CRANK GRINDER Equipped with: Landis 6400 CNC Control Siemens TOUCH HMI Arobetech Steady Rest Marposs P7 Gage System Lateral Locator Twin CBN Grinding Wheels Nodpfjrtrxxox Agzsdc Rotary Dresser Headstock Tailstock Rittal AC Units Specifications: Maximum Center Distance: 680 mm

Condition: good (used), Year of construction: 2015, machine/vehicle number: 190630, turning length: 150 mm, turning diameter: 200 mm, spindle bore: 42 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 50 rpm, travel distance X-axis: 150 mm, travel distance Z-axis: 155 mm, rapid traverse X-axis: 24 m/min, rapid traverse Z-axis: 24 m/min, turning diameter over bed slide: 220 mm, overall weight: 5,000 kg, spindle nose: 140 Flat, bar diameter (max.): 51 mm, power: 0.015 kW (0.02 HP), The innovative front-facing spindle of the 2SP-150H helps create an automation-friendly lathe for small parts production. By moving the spindle off the side and incorporating the Okuma Gantry Loader (OGL) into the production line, parts can be loaded and unloaded automatically. An extremely compact footprint improves floor space utilization, while the popular dual spindle option significantly reduces cycle time. Ndodpfx Aortrlzogzoc Equipped with: Okuma OSP-P300L CNC Control 8" 3-Jaw Chuck Expanding Mandrel Turret Tooling Gantry Loader Pendant Controller Chip Auger Stack Light

Condition: used, Year of construction: 1973, machine/vehicle number: 24109, Equipped with: Stock Divider Hydraulic Work Clamping Chip Conveyor Cutter Clamping Bolt Index Plate Change Gears Hydraulic System Coolant System Nsdpfexdfa Ujx Agzsdc Specifications: Min. Outside Cone Distance: 2.75" Max. Cone Distance: 10" Max. Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 6.8 to 16.5 RPM Feeds (seconds/tooth): 3 to 9 Main Motor: 5hp, 900 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approx. Floor Space: 118" x 86.5" Needed Overall Height: 70" Approx. Net Weight: 16,000 lbs Shipping Weight Boxed for Export: 17,000 lbs

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Njdsxdfazspfx Agzodc Index Plate Geneva Cam Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Base Work Holding Draw Bars Automatic Doors Spindle Chiller Ndedpfx Aexdfanogzoc Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), overall weight: 10,364 kg, Year of construction: 2019, 2019 GENERAL BROACH 10-30 GBTU VERTICAL TABLE UP BROACH Equipped with: Retriever Shuttle Table Chip Conveyor Auto Load Grayco Lube AB Panelview Coolant Tank & Pump Specifications: Ndedpfxortrzae Agzjc Capacity: 10 Ton Stroke: 30" Table Up 1″ Puller / Retriever Hydraulic Power Unit Chip Conveyor Machine Dimensions (approx.): 165″ x 48″ x 60″ Machine Weight Total (approx.): 22,800 lbs. Machine Column (approx.) : 13,000 lbs. Base w/ Chip Conveyor (approx.): 4,700 lbs. Electrical Panel (approx.): 600 lbs. Hydraulic Power Unit (approx.): 4,500 lbs.